It is blend of alkaline-based detergents, surfactants formulated with a strong foaming action designed to rapidly emulsify greasy soils and oxidation…thereby leaving coils dirt-free and shining. C-SHINE is recommended for cleaning air-cooled condensers, permanent filters and other finned heating and cooling coils.
In-service cleaning:-RXSOL-16-1668-025 is passes through the air trunking upstream of the charge aircooler, followed by a clean water rinse.For cleaning of air coolers, it is necessary to use correctly installed dosing and injection system.
Typical Cleaning Method :-
Dilute 1-3 parts water and apply with alow pressure sprayer. Leave on coils for 3-7 minutes then flush with water until all foam is removed. If use don built up roofsetc., it is important to make sure all residual cleaner is washed off roof surface after application. If good housekeeping practices are not followed, roof deterioration is possible. If used indoors, strong fumes may cause irritation to sensitive individuals evacuate area if necessary.
For cleaning of Air cooler and Air side of turbochargers, a solution of 5 - 25% RXSOL-16-1668-025 in fresh water is recommended. Inject the solution for 10-15minutes, then similar quantity of fresh water injected to rinse off emulsifieddeposits.
Handspray Cleaning:-
By Handspray,apply concentrate RXSOL-16-1668-025 all over the cooler coils. for good emulsification & penetration. Allow the RXSOL-16-1668-025 for a minimum of 1 hour,then use a light water pressure to wash off the loosened deposits. During process always keep drain valve open. After satisfactory cleaning, and flushing through with fresh water, close air cooler drains. Note that during this process the engine must be stopped.
Soak method:-
Machine parts with stubborn carbon deposits to be cleaned is dipped into conc.Soln.of RXSOL-16-1668-025 then allow deposits tobe broken down and loosened before removal, then rinse .
Precaution ::--
Avoid skin / eye contact. Wear gloves and goggles when using. Use in well ventilated areas. Donot breathe vapours.
| Method | Dilution / Concentration | Application Steps | Notes / Precautions |
|---|---|---|---|
| In-Service Cleaning | Undiluted or as per system specs | Pass through air trunking upstream of the charge air cooler. Follow with clean water rinse. | Use proper dosing and injection system. Ensure thorough rinse. |
| Typical Cleaning (Spray) | 1 part cleaner to 1–3 parts water | Apply using low-pressure sprayer. Leave for 3–7 minutes. Rinse thoroughly with water to remove all foam. | Remove all residues from roofs or surfaces to avoid deterioration. Fumes may cause irritation indoors. |
| Air Cooler / Turbocharger Cleaning | 5–25% in water | Inject cleaning solution for 10–15 minutes. Follow with equal quantity of fresh water for rinsing. | Ensure engine is off. Proper drainage required during the process. |
| Hand Spray Cleaning | Use concentrate | Spray directly on coils. Allow at least 1 hour for penetration. Rinse with high-pressure water. | Keep drain valve open during cleaning. Close after flushing. Engine must remain off. |
| Soak Method | Concentrated solution | Dip parts in solution. Allow time for deposits to loosen. Rinse thoroughly. | Ideal for stubborn carbon on metal machine parts. Wear protective gloves and goggles. |
| Appearance | Clear, Slight Yellow |
| Odor | Fresh |
| pH | Alkaline |
| Sp. Gravity | >1.15 |
Other Grade of Coil Cleaner :::
Coil Brite Rx Yellow - Part No.- RXSOL-16-1680-005 --- www.rxmarine.com/coil-brite
Coil Cleaner - Part No.- RXSOL-41-8672-025 --- www.rxmarine.com/Coil-Cleaner-RXSOL
Coil Cleaner ( Non Rinsing Type ) - Part No. - RXSOL-16-1697-025 --- www.rxmarine.com/coil-cleaner-non-rinsing
Condenser Coil Cleaner - Part No.- RXSOL-50-5015-025 --- www.rxmarine.com/Condensor-cleaner
Evaporator Coil Cleaner ::: Part No.- RXSOL-51-6004-025 --- www.rxmarine.com/evaporator-coil-cleaner
Coil Cleaner Free from ACID ::: Part No.- RXSOL-16-1082-025 --- http://rxmarine.com/Coil-Cleaner-Free-from-ACID
C-SHINE Alkaline coil cleaner ::: Part No- RXSOL-16-1668-025 --- www.rxmarine.com/C-SHINE-RXSOL-coil-cleaner
Why RXSOL-16-1668-025 preferred by our CUSTOMER ?
⇔ Reduce air-conditioning cost by allowing air-conditioning systems and units to run at maximum efficiency , Saves energy costs
⇔ A proper regular maintenance program including the use can substantially lengthen condenser life and save equipment replacement and downtime.
⇔ Cuts quickly through oily grime and Industrial air-borne impurities to restore condenser coils.
⇔ Due to its high penetration effect , Agitation or Scrubbing doesn't require
⇔ Simple spray on off operation to restores dirty condenser coils to peak efficiency
Characteristics
- Formulated to remove oil,grease & carbon deposits from air coolers & scavenging system
- Efficient and economical
- Renders surfaces oil-repellent
- Maintains and stabilizes air cooler efficiency at maximum
- Saves time, maintenance costs and avoids risks of damage when dismantling
- Leaves no residue and has no harmful effect on engine
- Product in water solution is non-flammable, non-explosive and has no flash point
- Can be used for light carbon removal from machinery parts
C SHINE coil cleaner specialized to remove dirt deposits, oily and greasy deposition from Condenser and Cooling coils. C-shine is specialized cleaning Chemical for Air Conditioner cleaning and Coil Cleaning.
C-Shine contains powerful selected alkaline additives with wetting agent and surfactant which helps to penetrates and remove dirt, grease and oil accumulation on evaporators and condenser coils quickly.
| Product Name | : | RXSOL-16-1668-025 |
| Product Type | : | C-SHINE RXSOL |
Company Details:
RX MARINE INTERNATIONAL
105, A wing , BSEL , TECH PARK.
VASHI ,NEW BOMBAY 400703 INDIA
Stock Point: Mumbai, Kandla, Kolkata, Vishakhapatnam, Chennai, Fujairah, Muscat Barka, Nairobi Kenya, Canada
| Phone | : | +91 22 65113333 / 5555 / 9999 / 27611360 |
| Fax | : | +91 22 2781 1318 :::AOH :0091 9821214367 |
| : | mail@rxmarine.com |
| Ingredients | CAS | % |
| Proprietory silicate compound | - | >60 |
| Ethoxylatednonylphenol | 9016-45-9 | 5-7 |
| Alkalline Agent | - | 10-15 |
| Disodium Metasilicate | 6834-92-0 | 4-6 |
| Sodium Dodecylbenzenesulfonate | 25155-30-0 | 3-5 |
| dipropylene glycol monomethyl ether | 34590-94-8 | 3-5 |
Irritating eyes possible redness and burns. Prolonged contact with skin cause sever burns.
Breath to spray mist can be
Irritation, If spill can causes slippery floor.
| Skin |
Corrosive, possible redness at point Remove contaminated clothing. Immediately wash contact and may cause sever burns of excess chemical with plenty soap and water. apply prolonged contact. emollient cream. Obtain medical attention |
| Eyes |
Corrosive, stinging with some redness irrigate immediately with plenty of water. Continue Possible cause corneal burns irrigation for at least 10 to 15 minutes. seek medical attention immediately |
| Ingestion |
Corrosive, Nausea, vomiting and stomach Do not induce vomiting which may contaminate the upset and pain occur lungs. If unconscious do not give anything by mouth.if necessary give artificial respiratory. If conscious give one pint of water to drink. Obtain medical attention immediately |
| Inhalation |
Inhalation of air mist during spray may Remove to fresh air. Rest, treat symptomatically, cause irritation of mucous membranes seek medical advice immediately. |
| Extinguishing Media | Product is non flammable |
| Special Protective Equipment |
Wear breathing apparatus and full protective clothing. Keep container cool by spraying with water if exposed to fire |
| Exposure Hazards | None |
Do not allow entry into drain, sewers and water courses. Mop up with absorbent material such as sand or earth.
Scrap or shovel up and transfer to a suitable container. Clean up affected area with plenty of water Prevent slip
hazards. See ‘Disposal Consideration’
Store in original container. Store separately from strong oxidising agents. Avoid contact with skin, eyes and clothing.
Keep out reach of children.
WEL= Workplace Exposure Limits PROTECTIVE EQUIPMENT:-
| Engineering Measures | Provide sufficient ventilation during operations which cause vapour formation. |
| Hands Protection | Use suitable protective gloves if risk of skin contact. |
| Eyes Protection | Wear approved safety goggle. |
| Other Protection | Wear appropriate clothing, respiratory to prevent any possibility of inhalation. |
| Hygiene Measures | Make eyes wash & showering accessible, wash at the end of each work shift and before eating, smoking using the toilet. |
| Appearance | : | Clear brownish liquid |
| Odour | : | NA |
| pH | : | Alkaline |
| Flash point | : | 100°C and above |
| Flammability | : | Non-flammable |
| Auto-flammability | : | Not determined |
| Relative density | : | 1.1 +/- 0.1 |
| Solubility | : | Soluble in water Complete |
| Stability | Stable |
| Conditions to Avoid |
Mixtures of acids, isocyanates, rapid addition to hot water. Will catalyze reacting of other chemicals |
| Incompatibility | Strong acids |
|
Hazardous decomposition products: |
Non |
| Hazardous polymerization | Will not occur |
Keep away from strong oxidising agent. (React with material): aluminum and their alloys, zinc and galvanise)
Corrosive, contact with eyes may cause to irritation and burns. Stinging and redness to skin, prolonged and repeated cause sever burns.
Inhalation breath to spray mist may sting to mucous membranes and/or cough and a sore throat.
The nature and severity of the acute effects precludes the likelihood of chronic exposure.
Biodegradability: Not Applicable Chemical Oxygen Demand ( mg.02/1): Not determined Aquatic toxicity studies have not been conducted
on this product.
Recycle used containers if facilities are available, if not incineration is recommended. Failing this, use landfill.
Be sure to comply with local authority regulation.
| Proper Shipping Name | : | Pottasium Hydroxide, Solution | |
| UN Number | : | 1284 | |
| ICAO-Air | : | Class 8 | Packaging group III |
| IMO Sea | : | Class 8 | Packaging group III |
| ADR Road | : | Class 8 | Packaging group III |
Supply classification: Corrosive Hazard pictogram: Risk phrases: R35 Causes sever burns R43 May cause sensitisation by skin contact.
Safety phrases: S24/25 Avoid contact with skin and eyes Corrosive S26 Incase of contact with eyes, rinse immediately with plenty of water
and seek medical advice
S27 Take off immediately all contaminated clothing
S28 After contact with skin, wash immediately with plenty water
S37/39 Wear suitable gloves and eye/face protection.
Data from the following sources have been used to compile this document.
HSE – EH40/93 Occupational exposure limits
HSE – EH29/93 Occupational skin diseases; Health and Safety Precaution
HSC – Safety Data Sheets for substances and preparation dangerous for supply.
Date of issue: 31.08.2010
DISCLAIMER OF LIABILITY :The information in this SDS was obtained from sources which we believe are reliable. However, the information is provided without any warranty, express or implied, regarding its correctness. The conditions or methods of handling, storage, use or disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the product. This MSDS was prepared and is to be used only for this product. If the product is used as a component in another product, this MSDS information may not be applicable.