Power of Chemical to break EMULSION in two phase hydrocarbon phase (oil) and a water-phase. We have whole range of demulsifier-chemicals for oil and industrial applications.
Dosage and application will vary based on emulsion characteristics. For most crude or fuel oil based emulsions, a starting concentration of 0.1% at 165°F with a minimum heated recirculation contact time of 2 hrs will achieve optimal break. However water separation can be achieved in many oil emulsions at temperatures below 100°F.
Water-In-Oil Demulsifiers, which can be used as stand-alone Demulsifiers to separate Formation Water from Crude Oil Emulsion. There are vast differences and Characteristics of Crude Oils produced in various Fields. Use and application Oil Soluble Demulsifier Testing & Selection is accomplished by standard Bottle Tests in Lab followed by Field Trial Tests. They are commonly used in the processing of crude oil for effectively separating formation water from emulsions in crude oil.
Dose recommendations have to be made on a case-by-case basis. The dosage rate varies and depends on nature copoaition of phase materials and it may varies from 5 to 10 ppm, so we suggest adding the lower levels to your laboratory bench tests to verify the correct dosage for the specific application. Finding the most cost-effective dosage, as well as determining the best conditions of temperature, slow mixing, settling time, etc., is best done in the laboratory, using a sample of the actual oil or waste and a sample of Demulsifier.
Typical method for Evalution of Demulsifier :
Step 1 :Treat 100ml of the emulsion with 40 mg/litre of Demulsifer, (using 1% w/v solution in xylene in 100 ml graduatd conical tube) and give 100 shakes of approximately 12 in stroke
Step 2 : Place treated emulsion in water bath maintained at 70 +1oC for a period of 15 minutes and allow it to settle for 5 minutes at 30+2oC. measure the quantity of clear water settled
Step 3 : Conduct a blank test with untrented emulsion under condition similar to treated emulsion
Step 4 : Substract the water seprator if any in blank test from treated sample and denote it as V. Similarly subtract the water separated from blank from total water present in emulsion and denote it Vo.
Report Efficiency Percentage as Follow : % Effiency =(V/ Vo) x 100
SPECIFICATIONS:
| Color: | Opaque white to yellow |
| Odor: | Sweet to Mild chemical odor Specific Gravity: 0.98 @25°C |
| Flash Point: | 200°F |
| pH (10%): | 5.63 |
| Solubility: | Water Dispersible |
Answer :
Reverse Demulsifiers—-Break oil-in-water emulsions
| Product Name | RXSOL-81-8159-210 |
| Product Type | Demulsifier ORG |
Company Details:
RX MARINE INTERNATIONAL
105, A wing , BSEL , TECH PARK.
VASHI ,NEW BOMBAY 400703 INDIA
Stock Point ::: Mumbai, Kandla, Kolkata, Chennai, Gandhidham, Fujairah, Visakhapatnam, Muscat
| Phone | +91 22 27815541 / 42 |
| Fax | +91 22 2781 1318 :::AOH :0091 9821214367 |
| mail@rxmarine.com |
Components
| Substance name | Contents | CAS No | EC No | Classification |
| Alkylated sulfonic acid derivates : | 25 - 50 % | 68584-22-5 | 271-528-9 |
Xn; R22 C; R34 |
| Solvent naphtha (petroleum), Heavy aromatic : | 50 - 80 % | 64742-94-5 | 265-198-5 | Xn; R65 |
| 1,2,4-trimethylbenzene : | 5 - 10 % | 95-63-6 | 202-436-9 |
R10 Xn; R20 Xi; R36/37/38 N; R51-53 |
| Naphthalene : | 1-3 % | 91-20-3 | 202-049-5 |
Carc. Cat. 3; R40 Xn; R22 N; R50-53 |
Risk Phrases : Causes burns. Harmful if swallowed. Limited evidence of a carcinogenic effect. Toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment.
Primary route of exposure : Vapours inhalation. Skin and eyes contact.
Symptoms relating to use
Inhalation : Cough. Sore throat. Shortness of breath. Corrosive to respiratory system.
Skin contact : Redness, pain. Causes burns.
Eye contact : Redness, pain. Blurred vision.
Burning sensation.
Risk of serious damage to eyes.
Ingestion : Abdominal pain, nausea. Burning sensation.
| Inhalation : | Assure fresh air breathing. Obtain medical attention if breathing difficulty persists. |
| Skin contact : |
Remove affected clothing and wash all exposed skin area with mild soap and water, followed by warm water rinse. Seek medical attention if irritation develops. |
| Eye contact : | Rinse immediately with plenty of water. Contact ophthalmologist immediately. |
| Ingestion : | Rinse mouth. Do not induce vomiting because of corrosive effects. Call a physician immediately. |
| Extinguishing media : | All extinguishing media can be used. |
| Specific hazards : | High temperature may liberate dangerous gases. |
| Protection against fire : |
Do not enter fire area without proper protective equipment, including respiratory protection. |
| Special procedures : | Exercise caution when fighting any chemical fire. |
| Personal precautions : | Equip cleanup crew with proper protection. Respiratory protection equipment may be necessary. |
| Environmental precautions : | Prevent entry to sewers and public waters. Notify authorities if product enters sewers or public waters. |
| Clean up methods : | Clean up any spills as soon as possible, using an absorbent material to collect it. Dilute residues and flush. |
| Precautions in handling and storage : | Good ventilation of the workplace required. |
| Storage : | Store in dry, well-ventilated area. Do not store in corrodable metal. |
| Storage - away from : | Strong bases. |
| Handling : |
Ensure prompt removal from eyes, skin and clothing. Wash hands and other exposed areas with mild soap and water before eat, drink or smoke and when leaving work. |
| Respiratory protection : |
Approved dust or mist respirator should be used if airborne particles are generated when handling this material. |
| Hand protection : | Gloves. |
| Skin protection : |
If skin contact or contamination of clothing is likely, protective clothing should be worn. |
| Eye protection : | Safety glasses. |
| Ingestion : | When using, do not eat, drink or smoke. |
| Industrial hygiene : |
Provide local exhaust or general room ventilation to minimize dust and/or vapour concentrations. |
| Physical state at 20 °C : | Liquid. |
| Colour : | Hazzy Liquid. |
| Odour : | Pungent. |
| Pour point [°C] : | -10 |
| Boiling point [°C] : | 205 |
| Density [kg/m3] : | 0,96 (20 C) |
| Viscosity at 20°C [mPa.s] : | 500 |
| Solubility in water : | In water, the material disperses. |
| Flash point [°C] : | 87 |
| Explosion limits - lower [%] : | 1,0 |
| Explosion limits - upper [%] : | 8,0 |
| Hazardous decomposition products : | According to process conditions, hazardous decomposition products may be generated. |
| Hazardous reactions : | Reacts violently with : Bases. |
| Hazardous properties : | Attacks metals |
No Information Available
No Information Available
General : Dispose in a safe manner in accordance with local/national regulations.
Labelling ADR {
- Proper shipping name : UN3265 CORROSIVE LIQUID, ACIDIC, ORGANIC, N.O.S. (Alkylated sulfonic
acid derivates), 8, III, (E)
Shipping name : UN3265 CORROSIVE LIQUID, ACIDIC, ORGANIC, N.O.S. (Alkylated sulfonic
acid derivates), 8, III, (E)
UN No. : 3265
H.I. nr : 80
- Tremcard nr. : 80GC3
ADR/RID : Class : 8
| Symbol : |
C : Corrosive N : Dangerous for the environment |
| R Phrase : |
R22 : Harmful if swallowed. R34 : Causes burns. R40 : Limited evidence of a carcinogenic effect. R51/53 : Toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment. |
| S Phrase : |
S26 : In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. S36/37/39 : Wear suitable protective clothing, gloves and eye/face protection. S45 : In case of accident or if you feel unwell, seek medical advice immediately ( show the label when possible). S61 : Avoid release to the environment. Refer to special instructions/Safety data sheets. |
The contentsof this MSDS are in base of our knowledge. However, the information is provided without any warranty, express or implied, regarding its correctness. The conditions or methods of handling, storage, use or disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the product. This MSDS was prepared and is to be used only for this product.
DISCLAIMER OF LIABILITY :The information in this SDS was obtained from sources which we believe are reliable. However, the information is provided without any warranty, express or implied, regarding its correctness. The conditions or methods of handling, storage, use or disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the product. This MSDS was prepared and is to be used only for this product. If the product is used as a component in another product, this MSDS information may not be applicable.